Products

FM GOSAG DENSIMETRIC TABLE

The FM type is used to treat products with low density and medium granulometry. Robust designed with wear elements provided for hard work conditions. There are 4 versions depending on the width (0.7, 1, 1.5 and 2.4m). It can be supplied with or without dedusting system. Dedusting system by cyclone or by sleeve filter.

Download Catalogue: Catalogue
Download Inquiry Form: Form

GSort DENSIMETRIC TABLE

The GSort’s density separation process is based on a tilted, vibrating deck.

An upward stream of air passes through this deck, having two important effects on the materials being separated:

• Materials with a lower density will move downwards, without any contact with the deck, as a result of the inclination.
• Materials with a higher density will stay in contact with the deck and be conveyed upwards by the vibration.
Endorsed by its efficiency and lower ecological footprint, which makes it one of the teams with less impact, more sustainable and respectful of the market environment.

Download Catalogue: GSort
Download Inquiry Form: Form

TYPE MSizer EXTEND

Economical, efficient and environmentally friendly.

Con la nueva criba M ampliada, ALLGAIER-Group introduce la detección de material a granel en una nueva era.

The MSizer extend is based on the same Sizer principle developed and proven by Fredrik Mogensen more than five decades ago. The MSizer extend combines state-of-the-art technology with decades of extensive knowledge and expertise.

The result is an even more accurate screening process with increased throughput in a smaller footprint.

High efficiency with significantly reduced operating costs:

• up to 20% reduced energy consumption
• shorter set-up times
• simple screen replacement requiring only one person
• outstanding price/ performance ratio

Options:
• Machine monitoring
• ATEX design
• Lining heating

Download Catalogue: Catalogue
Download Inquiry Form: Form

TYPE MSizer COMPACT

The Mogensen MSizer compact is a compact short-deck sizer with high screening efficiency and large capacity on a small footprint.

It's driven by a single vibrator resulting in the typical elliptical motion that counteracts blinding of the screens, loosens and stratifies the feed material which secures an efficient material spread. Thus the MSizer Compact achieves a throughput of over 40 t / h e.g. for feed screening.

MOGENSEN SIZER TYPE E

The MOGENSEN Sizer type E executes a variable elliptical movement along the mesh, making the classification effectiveness grow. It was created to improve the old MOGENSEN S model (with two vibrators and a short mesh of 1.300 mm).

• One vibrator
• It can use up to 5 mesh decks to obtain up to 6 different products depending on the distribution curve of the material.
• High efficiency classification.

Download Catalogue: Catálogo Cribas Mogensen
Download Inquiry Form: Form

MOGENSEN TYPE SEL

The MOGENSEN Sizer type SEL is provided with two vibrators. It doubles the length of the mesh and reduces the meshes slope, increasing the capacity without loss of effectiveness.

Characteristics:

It uses up to 6 meshes decks to obtain 7 different products depending on the distribution curve of the material.

OTHER MOGENSEN SIZERS

Criba 3000, la más grande de la familia MOGENSEN.
- Suitable for higher flow jobs.
- Operates with exciters instead of vibrators.

GOSAG DESANDERS

Allgaier Mogensen desanders are used principally for water recovering with bentonite in drilling during foundations are being constructed.
These machines separate the debris permitting to reuse bentonite with water that it’s used as pumping medium. Also, it can be used in process where is required the separation by hidrocyclone to a smaller size that the get it with sandwashing units; for example cement mixer's cleaning.

Demonstrated advantages:
• Previous screening to get separate coarse materials; although these products are very sticky.
• Classified efficiency, a unique cyclone is enough for sandwashing plants designated for construction (100% nominal rate); however for sandwashing plants with really fine sand it is necessary a double cyclone (it can be treated till 150% of nominal rate, depending on the sludges content).
• Easy handling and robustness.

Escurridores GOSAG

Allgaier Mogensen desanders are used principally for water recovering with bentonite in drilling during foundations are being constructed.
These machines separate the debris permitting to reuse bentonite with water that it’s used as pumping medium. Also, it can be used in process where is required the separation by hidrocyclone to a smaller size that the get it with sandwashing units; for example cement mixer's cleaning.

The GOSAG recoveries of fine sand are used for recovering, by means of hydrocyclones, fine sand which is lost because of the overflow of washing equipments, like wheel washers or washing screws.
The main difference with a sand washing unit is that the draining stage is optional, depending on if it is necessary to drain the mixing of washed/ recovered sand while crossing the wash element.

GOSAG COMPACT SANDWASHING UNITS

These equipments were developed to wash sand although they are used too to wash minerals, purification of rivers and lakes, granulometric curves recomposition, contaminated grounds treatment, bentonite sludges treatment, etc.

In this types of applications, throwput and efficiency of these equipment are higher than the other machines as waterwheel or washing worms, getting always good quality sands due to a bigger friction capacity between particles and the biggest fines' sand recuperation (from 50 microns depending on the cyclone diameter).

The use of hidrocyclones or cyclones in the sand washing groups is most efficiency method for a good washing, understanding like this wash that let remove a fraction under 63 microns without fines lost.

OTHER GOSAG SANDWASHING EQUIPMENT

After the washing of material any stage two major problems:

- The treatment of the sludge generated in the washing process.
- The recovery of water for recirculation.
The solution is obtained from a common form installing a sludge with a dissolution of flocculant decanter.

Clarifiers:
Dirty water obtained from the process enters the clarifier by mixing box and receives the flocculant dissolution; his concentration and amount are very important for optimal performance.
In the box, are forced to mix the dirty water and flocculant to a specific route, forming the flocs with appropriate size and constitution. After the tour, the mixture enters deposit by the central chimney, where the mud starts to decide quickly to the bottom.

Autofloc:
Control of flocculant automatic system through a control system that regulates the cycles.

Controlfloc:
Equipment that automates the control of flocculant dosage. The computer automates the operation taking continuous samples of the mixture of dirty water and flocculant, analyzing the times of flocculation and the quality of the water.

RV GOSAG

Vertical distributor designed for the distribution of a central inlet flow, concentrated in one or two equal flow outlets along a bigger distance.

Its principal application is to open the product to proccess the whole wide of our MOGENSEN screening machines or GOSAG densimetric separation equipments, maximizing efficiency, especially when the wide is higher to 1m.

Also valid to distribute another kind of sizers, belt conveyors, etc. by outlets designed according to your requirements.

Capacity:
Capacity up to 1000 t/h depending to the product density and granulometry.

Download Inquiry Form: Form

TMS GOSAG

Horizontal distributor designed to distribute an incoming side located flow for its vibrating distribution to one, two or even three outlets placed along an equal or bigger distance. Multiple outlets types let adjust the outflow of each one.

Its principal application is to open the product to proccess the whole with of our MOGENSEN screening machines or GOSAG densimetric separation equipments, maximizing efficiency, specially if width is higher to 1m.
Also valid for distribute other sizers, belt conveyors, etc. by outlets designed according to your requirements.

Capacity:
Capacity up to 450 t/h depending on the product density, granulometry and the installation angle.

Download Inquiry Form: Form

GOZAG GRIZZLY

Grizzly feeder designed to be installed prior to a crushing system in order to avoid the entry of fine material, which prevents unnecessary wears or overloadings.

Characteristics:
Built in high thickness steel, they can support rock impacts up to 1.000mm edge. Also provided with antiwear covering of different thickness to ensure a long life of the machine.

Depending on the required capacity, one or two longitudinal bars in steel allow the feeder to prescreen the material. Built in manganese steel foundry and installed on a support frame that guarantees the separation between them.
Download Inquiry Form: Form

GOSAG TS

Available in 4 different constructions depending on the plate thickness in which they are manufactured, and hence its robustness:

• TS1
• TS2
• TS3
• TS4

Besides the various lengths and widths for the trough according to the requirements of flow feed or granulometry.

OTHER VIBRATING FEEDERS

Our product line includes a wide variety of vibrating feeders that can be adapted to all your specific needs, from 3 to 300 tonnes per hour, with different possible configurations.

Longitudinal vibrating feeders
• AL 2 vibrators up to 100t/ h
• TR1 2 vibrators up to 300t/ h
• SR1 1 vibrator up to 150t/ h

Tubular vibrating feeders
• TC 2 vibrators up to 50m3/ h

Rectangular vibrating feeders
• TTR 2 vibrators up to 50m3/ h

Download Inquiry Form: Form